Unit Price:$0
Ext Price:$0



Diodes Incorporated AP7361C-33SP-13 is a fixed 3.3 V low-dropout regulator with active-high enable. The 33 code selects the output, SP selects the eight-lead SO-8EP package with exposed ground pad, and -13 denotes 13-inch tape and reel. LCDChip's original package name is 8-SOIC (0.154", 3.90mm Width) Exposed Pad.
The AP7361C family supports fixed and adjustable output options up to 1 A. For AP7361C-33SP-13, the manufacturer's ordering key identifies the fixed 3.3 V option and the standard SO-8EP pin configuration. EN high turns the device on. Current limit, fold-back short-circuit behavior and thermal shutdown provide fault protection. The SP pinout differs from the reverse SPR variant.
No feedback divider is required.
EN permits intentional rail switching.
Supports local loads when headroom and board cooling allow.
Offers a direct board-level thermal path.
Diodes Incorporated defines SP as SO-8EP. LCDChip's original package entry is 8-SOIC (0.154", 3.90mm Width) Exposed Pad. The registered JPG depicts a generic eight-lead outline; its underside pad is not visible in the illustration. Use the manufacturer's SO-8EP mechanical drawing for the pad dimensions and land pattern. Connect the exposed pad to ground.

The manufacturer's SO-8EP top view assigns pin 1 OUT, pin 2 EN, pin 3 NC, pin 4 GND, pins 5–7 NC and pin 8 IN. The exposed pad is GND. The SO-8EPR reverse variant has a different assignment and must not be used for this SP device.
| Nominal output | Fixed 3.3 V |
|---|---|
| Recommended input | 2.2 V to 6.0 V, with output headroom |
| Recommended output current | 0 A to 1.0 A, subject to thermal limits |
| 3.3 V dropout at 1 A | 360 mV typical under datasheet conditions |
| Output accuracy | ±1% stated by Diodes Incorporated |
| Quiescent current | Approximately 60 µA typical under datasheet conditions |
| Output capacitor | At least 2.2 µF effective value |
| Recommended ambient | −40°C to +85°C |
| Package | SO-8EP SP with exposed GND pad; LCDChip eight-lead SOIC exposed-pad name |
Typical values are condition-dependent. Use Diodes Incorporated's electrical tables for worst-case design and account for effective capacitor value after voltage and temperature derating.
Compare fixed 3.3 V output, 6 V input ceiling, EN polarity, 1 A load, capacitor requirements, all eight pin positions and exposed-pad connection. SO-8EPR has a different pinout; SOT89-5 and other AP7361C packages are not footprint interchangeable. No LCDChip internal alternative is linked without an exact production API match and circuit review.
Diodes Incorporated AP7361C datasheet DS37274 Rev. 5-2 (October 2020) defines the 33 fixed output, SP SO-8EP package, -13 tape-and-reel code, top-view pinout, operating limits and capacitor guidance. Consult the current controlled datasheet and mechanical drawing before design release.
Local 3.3 V rail in compatible monitor circuitry.
Enabled point-of-load supply from a suitable input.
Switched 3.3 V supply with exposed-pad heat spreading.
Compact linear regulation after board thermal review.
Check the full AP7361C-33SP-13 code on the reel label, lot traceability, eight-lead body, exposed pad and manufacturer's marking. Verify pin-one orientation and test 3.3 V regulation with a current-limited fixture, suitable capacitors and defined EN level. Compare marking with current manufacturer records.
No. The 33 code is fixed nominal 3.3 V.
EN, an active-high enable input on the SP pinout.
Ground, along with pin 4.
No. Diodes Incorporated assigns a different pinout to SO-8EPR.
Use at least 2.2 µF effective value and follow the manufacturer layout guidance.
Check input-output headroom, EN thresholds, capacitor derating, exposed-pad ground connection and junction temperature at maximum load. Current limit and thermal shutdown are protective functions, not normal operating conditions.
The following parts include "AP7361C-33SP-13" in Silicon Labs AP7361C-33SP-13.
The following parts are popular search parts in Test and Measurement.