Unit Price:$0
Ext Price:$0



BD33HA3VEFJ-ME2 is a fixed-output member of ROHM's BDxxHA3MEFJ-M automotive low-dropout regulator family. It supplies a nominal 3.3 V rail at up to 300 mA when the input voltage and thermal design meet the data sheet limits.

This regulator combines a fixed 3.3 V output, enable control, overcurrent protection and thermal shutdown in ROHM's HTSOP-J8 package. The catalog lists an 8-SOIC, 0.154-inch-wide exposed-pad outline; use ROHM's HTSOP-J8 mechanical drawing and land pattern to design the PCB.
The BDxxHA3MEFJ-M family is specified for automotive applications and a -40 °C to +105 °C ambient operating range. The device uses a low-dropout linear topology and requires input and output ceramic capacitors for stable operation. Shutdown current is typically 0 µA at the data sheet test condition, with a 5 µA maximum.
Registered package: 8-SOIC (0.154", 3.90mm Width) Exposed Pad. ROHM designates its physical case HTSOP-J8. The image above is a package-class illustration, not a dimensioned drawing. Check pin-1 orientation, exposed-fin connection, dimensions and recommended footprint in the manufacturer's data sheet before layout.
| Pin | Name | Function |
|---|---|---|
| 1 | VO | Regulated 3.3 V output. |
| 2 | VO_S | Output-sense pin; connect to VO on the PCB. |
| 3 | GND | Ground. |
| 4, 6, 7 | NC | No internal connection; may be left open or tied to GND as allowed by ROHM. |
| 5 | EN | Enable control input. |
| 8 | VCC | Input supply. |
Connect the exposed FIN/substrate to GND according to the manufacturer guidance.
| Parameter | Value / condition |
|---|---|
| Orderable model | BD33HA3VEFJ-ME2 |
| Nominal output voltage | 3.3 V fixed |
| Maximum output current | 300 mA |
| Recommended VCC | 4.5 V to 8.0 V; sufficient input-to-output headroom is also required |
| Output accuracy | ±1% at 25 °C and no load; ±3% over -40 °C to +105 °C and no load |
| Operating ambient temperature | -40 °C to +105 °C |
| Input / output capacitors | At least 1.0 µF ceramic each, subject to ROHM's stability and layout guidance |
Select this exact 3.3 V variant when the downstream rail and load-current requirements match its fixed output. Confirm the input stays above the output by the required dropout margin at worst-case load and temperature; the family input range alone does not guarantee regulation for every output variant. For the 5.0 V option, headroom is especially important near the 4.5 V lower family supply limit. Calculate power dissipation as approximately (VCC - VO) × load current plus quiescent loss, and verify junction temperature with the actual PCB copper and airflow.
Manufacturer: ROHM Semiconductor. Primary technical source: ROHM BDxxHA3MEFJ-M series data sheet, Rev.002. The ordering table identifies BD33HA3VEFJ-ME2 as the fixed 3.3 V variant. Consult that document for electrical limits, test conditions, recommended circuit, handling and the latest package drawing.
Suitable design targets include local regulated rails in automotive electronic modules, sensor interfaces and control circuits where the supply, current and thermal limits are satisfied. Validate transient behavior, noise, protection response and qualification requirements in the end application.
Match the full manufacturer part number and package markings against the purchase and inspection records. Verify the device's orientation and solder joints after assembly. The catalog package image is illustrative; the ROHM data sheet controls component dimensions and electrical specifications.
No. BD33HA3VEFJ-ME2 is the fixed 3.3 V variant; VO_S is an output-sense connection, not a resistor-programming pin.
No. Maintain the required VCC-to-VO headroom for the selected output, load and temperature.
Connect VO_S to the VO output node as shown in ROHM's recommended circuit.
Values above summarize the manufacturer data sheet and retain its stated conditions. Confirm current revision, absolute maximum ratings, capacitor characteristics, thermal design, PCB footprint and application-level tests before release. No real-time pricing or inventory information is asserted here.
The following parts include "BD33HA3VEFJ-ME2" in Silicon Labs BD33HA3VEFJ-ME2.
The following parts are popular search parts in Test and Measurement.