Unit Price:$0
Ext Price:$0



Texas Instruments LM340S-5.0/NOPB is a three-terminal positive linear regulator for a fixed 5 V rail, with output-current capability up to 1.5 A when thermal conditions are properly managed.
The exact orderable uses the KTT DDPAK/TO-263 surface-mount package and is rated for a 0 to 125 degrees C operating-junction range.
LM340S-5.0/NOPB is the 5 V member of the LM340 family. It combines a monolithic series regulator with internal current limiting, thermal shutdown, and safe-operating-area protection. The device is intended for local regulation, distributed power rails, and other circuits that need a conventional fixed 5 V supply.
Provides a familiar regulated rail without an external feedback divider.
Supports substantial load current when input headroom, PCB copper, and thermal limits are satisfied.
Current limiting, thermal shutdown, and safe-area compensation protect the regulator under abnormal conditions.
No output capacitor is required for stability, although a small capacitor can improve transient response.
The family is designed for input voltages up to 35 V; use the electrical table to determine the regulated operating range for the load.
The LM340/LM7805 table specifies 4.8 V to 5.2 V at 25 degrees C and 4.75 V to 5.25 V over the stated line, load, and temperature conditions.
Three functional pins provide input, ground, and regulated output.
The KTT TO-263 body provides a soldered thermal interface for PCB heat spreading.
Texas Instruments identifies this exact orderable as KTT DDPAK/TO-263 with three functional pins and a 4.83 mm maximum-height mechanical outline. The catalog package name D2PAK (3 leads plus tab) corresponds to this power-package family.

The KTT outline also includes a large soldered tab or exposed thermal feature. Follow the TI package and device drawings when assigning and routing that feature; do not substitute a generic TO-263 footprint without verification.
| Manufacturer | Texas Instruments |
|---|---|
| Function | Fixed positive linear voltage regulator |
| Nominal output | 5 V |
| Output at 25 degrees C | 4.8 V minimum, 5 V typical, 5.2 V maximum |
| Output over stated line, load, and temperature | 4.75 V minimum, 5.25 V maximum |
| Output-current capability | Up to 1.5 A, subject to thermal limits |
| Maximum family input rating | 35 V |
| Typical dropout at 1 A | 2 V |
| Quiescent current at 25 degrees C | 8 mA typical |
| Output noise, 10 Hz to 100 kHz | 40 microvolts typical |
| Ripple rejection at 120 Hz | 62 dB minimum, 80 dB typical at the stated condition |
| Operating junction range | 0 to 125 degrees C |
| Package | KTT DDPAK/TO-263, three functional pins |
| Standard package quantity | 45, tube |
| Lifecycle | Active production |
Match the fixed 5 V output, current rating, dropout and minimum input headroom, 35 V absolute input limit, KTT footprint and tab geometry, pin assignment, junction-temperature range, transient behavior, protection functions, and thermal performance.
No internal alternative is linked because no exact substitute was confirmed through the production API.
Texas Instruments data sheet SNOSBT0L documents the LM340 family pin functions, 5 V electrical characteristics, application guidance, thermal behavior, and KTT mechanical information. The exact manufacturer listing identifies LM340S-5.0/NOPB as active production in KTT TO-263, three pins, with tube packing.
Provides point-of-load regulation near digital, analog, or mixed-signal circuits.
Reduces noise and wiring-drop problems associated with a single remote regulator.
Generates a stable 5 V supply from a higher-voltage DC source.
Creates a clean fixed rail after a preregulated supply when efficiency and heat are acceptable.
Verify the complete LM340S-5.0/NOPB orderable code, Texas Instruments traceability, LM340S -5.0 P+ device marking, KTT mechanical dimensions, lead finish, moisture-sensitivity label, and tube documentation. Confirm that the received package matches the current manufacturer drawing before assembly.
No. This exact orderable is the fixed 5 V version.
Only when input headroom, copper area, ambient conditions, and junction temperature keep the device within its thermal limits.
It is not required for stability. Texas Instruments notes that 0.1 microfarad can improve transient response.
Use at least 0.1 microfarad when the regulator is more than approximately six inches from the supply filter capacitor; place it close to the device.
The typical dropout at 1 A is 2 V, but the guaranteed regulation conditions and transient margin must be taken from the electrical table for the actual load and temperature.
Validate worst-case input voltage, dropout, load steps, line transients, short-circuit behavior, input and output bypassing, PCB copper, exposed-tab land pattern, ambient temperature, and junction temperature against the current TI data sheet. Linear-regulator dissipation can become the dominant constraint well below the nominal output-current rating.
The following parts include "LM340S-5.0/NOPB" in Silicon Labs LM340S-5.0/NOPB.
The following parts are popular search parts in Test and Measurement.