Unit Price:$0
Ext Price:$0



STMicroelectronics LF33CDT-TR is a fixed 3.3 V positive linear regulator in a three-terminal DPAK package, rated for output current up to 500 mA under the conditions and thermal limits in the manufacturer data sheet.
Technical information is based on STMicroelectronics LFXX data sheet DocID2574 Rev 31 and the current manufacturer product record. Verify electrical, thermal, capacitor, and package requirements in the latest documentation before design release.
LF33CDT-TR is the fixed 3.3 V, C-grade member of the LFXX low-dropout regulator family. The three-terminal DPAK version is permanently enabled and combines a low-dropout architecture with internal current limiting and thermal protection.
The part is intended for local regulation where low quiescent current and modest input-to-output headroom are useful. The design must still satisfy the data-sheet input range, output-capacitor ESR, junction-temperature, and power-dissipation limits.
Provides a nominal 3.3 V rail with C-grade ±2% initial selection at 25°C.
Supports loads up to 500 mA subject to dropout and thermal conditions.
Typical dropout is 0.2 V at 200 mA and 0.4 V at 500 mA.
Includes internal current limiting and thermal limiting.
The registered package is TO-252-3, DPAK (2 Leads + Tab), SC-63. ST lists LF33CDT-TR as a DPAK tape-and-reel order. Confirm the current manufacturer drawing, top-view orientation, land pattern, stencil, and thermal copper before layout.

Positive supply input; use local bypassing according to the data sheet.
Ground reference. The exposed tab is also electrically connected to ground.
Regulated fixed 3.3 V output; connect the required stability capacitor to ground.
Confirm pin numbering and top-view orientation against the latest ST DPAK package drawing before PCB routing.
| Regulator type | Fixed positive low-dropout linear regulator |
|---|---|
| Nominal output voltage | 3.3 V |
| Initial output range | 3.234 V to 3.366 V at VIN = 5.3 V, IOUT = 50 mA, TJ = 25°C |
| Operating input voltage | Up to 16 V at 500 mA in the LF33C electrical-characteristics table; maintain dropout headroom |
| Output current | Up to 500 mA, thermally limited |
| Current limit | 1 A typical |
| Dropout voltage | 0.2 V typical / 0.35 V maximum at 200 mA; 0.4 V typical / 0.7 V maximum at 500 mA |
| Quiescent current | 0.5 mA typical, 1 mA maximum at no load under stated conditions |
| Line regulation | 3 mV typical, 16 mV maximum from 4.3 V to 16 V at 5 mA |
| Load regulation | 3 mV typical, 16 mV maximum from 5 mA to 500 mA at VIN = 4.6 V |
| Supply-voltage rejection | 80 dB typical at 120 Hz; 75 dB typical at 1 kHz; 65 dB typical at 10 kHz |
| Output noise | 50 µV typical, 10 Hz to 100 kHz |
| Output capacitor | 2.2 µF minimum; specified ESR range 0.1 Ω to 10 Ω, up to 10 µF in the test table |
| Operating junction temperature | −40°C to +125°C |
| Absolute maximum input | −0.5 V to 40 V; for 18 V < VIN < 40 V the regulator is in shutdown |
| Package thermal resistance | 8°C/W junction-to-case and 100°C/W junction-to-ambient for DPAK/PPAK test conditions |
No drop-in replacement is asserted. Compare fixed output voltage, accuracy grade, current capability, input range, dropout, quiescent current, DPAK pinout and tab connection, capacitor value and ESR, package dimensions, tape orientation, protection behavior, and thermal performance before substitution.
STMicroelectronics LFXX data sheet DocID2574 Rev 31 identifies LF33CDT-TR as the 3.3 V C-grade order in DPAK tape-and-reel packaging. The C grade is the ±2% selection at 25°C.
This exact order is a three-terminal DPAK device and is therefore fixed in the ON state; the logic-controlled inhibit function described for the five-pin PPAK version is not available on this order.
Post-regulation for logic, control, and mixed-signal circuits within the electrical limits.
Low-dropout regulation where input headroom and quiescent current matter.
Local 3.3 V supply generation with appropriate thermal and transient design.
Linear post-regulation when switching ripple or supply noise must be reduced.
Check complete marking, package, lot/date traceability, and handling condition against purchase documentation. Follow manufacturer ESD, moisture, storage, and reflow guidance; appearance alone does not establish authenticity or electrical performance.
It is the fixed nominal 3.3 V C-grade member of the LFXX family.
No. The three-terminal configuration is fixed in the ON state; inhibit control belongs to the five-pin PPAK configuration.
The data sheet specifies at least 2.2 µF, with ESR from 0.1 Ω to 10 Ω under the stated test conditions.
The electrical rating is up to 500 mA, but actual continuous current is constrained by input headroom, dropout, board thermal design, ambient temperature, and junction-temperature limits.
Estimate power dissipation from (VIN − VOUT) × IOUT plus ground-current losses. Validate stability with the selected capacitor over tolerance, bias, temperature, and ESR. Confirm transient behavior, reverse-current conditions, absolute maximum ratings, junction temperature, and the latest ST documentation before production release.
The following parts include "LF33CDT-TR" in Silicon Labs LF33CDT-TR.
The following parts are popular search parts in Test and Measurement.